Balloon Task
- Primate
- Member
- Posts: 409
- Joined: January 15th, 2009, 4:34 pm
- Division: C
- State: NY
- Has thanked: 0
- Been thanked: 0
Re: Balloon Task
Don't forget that sand timers will have five to ten seconds of variability, depending on how fast the non sand timer tasks take. Also, I see this more as an engineering project than a science experiment. You have to design your device to overcome these random factors, however unfair, rather than .
Not that a problem like this wouldn't be frustrating.
Not that a problem like this wouldn't be frustrating.
events 2012 gravity vehicle, robot arm, thermodynamics, tps
- illusionist
- Member
- Posts: 942
- Joined: March 20th, 2010, 4:13 pm
- Division: C
- State: MI
- Has thanked: 0
- Been thanked: 1 time
Re: Balloon Task
I am using baking soda and vinegar to inflate my balloon. The balloon then hits a switch. The problem is that the balloon takes different amounts of time every other run. Are your reactions reliable? If not, what did you do to fix the problem?
- Primate
- Member
- Posts: 409
- Joined: January 15th, 2009, 4:34 pm
- Division: C
- State: NY
- Has thanked: 0
- Been thanked: 0
Re: Balloon Task
Are you using the exact same amount of baking soda/vinegar each run? If not, measure it out and see if that helps. (Ours never varied by a more than a second, which was perfect.)illusionist wrote:I am using baking soda and vinegar to inflate my balloon. The balloon then hits a switch. The problem is that the balloon takes different amounts of time every other run. Are your reactions reliable? If not, what did you do to fix the problem?
events 2012 gravity vehicle, robot arm, thermodynamics, tps
-
- Exalted Member
- Posts: 292
- Joined: March 24th, 2011, 10:28 am
- Division: Grad
- State: NY
- Has thanked: 0
- Been thanked: 0
Re: Balloon Task
Also, have the balloon only need to expand minimally to push the switch. The more expanding necessary, the less reliable the timing will be.
- illusionist
- Member
- Posts: 942
- Joined: March 20th, 2010, 4:13 pm
- Division: C
- State: MI
- Has thanked: 0
- Been thanked: 1 time
Re: Balloon Task
We measure out the baking soda with a teaspoon, and the vinegar with a syringe; so I know that the amounts are consistent every time. I'll try minimizing the amount of inflation needed.
-
- Staff Emeritus
- Posts: 395
- Joined: January 11th, 2009, 7:10 am
- Division: Grad
- Has thanked: 0
- Been thanked: 0
Re: Balloon Task
You have a half hour to set up and practice. You can test the exact buoyancy of your balloon at that location during that time and fine tune the mass of your sign.old wrote: The answer you seem to be suggesting is to arbitrarily carry a certain amount of extra buoyancy (how much? enough for a 0.1 M/S down draft or a 1/M/S updraft?) and hope you made the right choice.
When it comes to the future, there are three kinds of people: those who let it happen, those who make it happen, and those who wonder what happened.
- illusionist
- Member
- Posts: 942
- Joined: March 20th, 2010, 4:13 pm
- Division: C
- State: MI
- Has thanked: 0
- Been thanked: 1 time
Re: Balloon Task
For that reason, I have made my mass adjustable. Basically I use clay to add or remove mass from my sign. There is a little container on the bottom of the sign to hold the clay.
- NinjaChicken
- Member
- Posts: 67
- Joined: March 30th, 2011, 5:08 am
- Division: C
- State: MI
- Has thanked: 0
- Been thanked: 0
Re: Balloon Task
That's almost exactly what I did. I made the 'sign' out of a napkin, and folded it like an envelope so I could add mass to it as needed.illusionist wrote:For that reason, I have made my mass adjustable. Basically I use clay to add or remove mass from my sign. There is a little container on the bottom of the sign to hold the clay.
- illusionist
- Member
- Posts: 942
- Joined: March 20th, 2010, 4:13 pm
- Division: C
- State: MI
- Has thanked: 0
- Been thanked: 1 time
Re: Balloon Task
Just saying, I think this is the balloon inflation task. The sign stuff should go over to the Sign Task thread.
So I'm going to carry this discussion over to that thread.
So I'm going to carry this discussion over to that thread.
Who is online
Users browsing this forum: No registered users and 3 guests