Mousetrap Vehicle B

User avatar
SirBobo
Member
Member
Posts: 87
Joined: October 24th, 2011, 8:17 pm
Division: B
State: CA

Re: Mousetrap Vehicle B

Postby SirBobo » December 29th, 2011, 3:45 pm

we had the same problem..... we switched to dvds and they work better.

Also... The rules say the trigger has 2 be vertical?
The trigger PENCIL has to be held vertically when pressing the metal/plastic bait pedal. Hope that cleared it up. :D
I am SirBobo and I approve this message

"Insert meaningful quote here"

Image Image

User avatar
SirBobo
Member
Member
Posts: 87
Joined: October 24th, 2011, 8:17 pm
Division: B
State: CA

Re: Mousetrap Vehicle B

Postby SirBobo » December 29th, 2011, 6:34 pm

There is no rule about what material to use for the car, right? (sorry double post) ಠ_ರೃ
Last edited by SirBobo on January 2nd, 2012, 1:31 pm, edited 1 time in total.
I am SirBobo and I approve this message

"Insert meaningful quote here"

Image Image

Gemma W
Member
Member
Posts: 196
Joined: March 10th, 2011, 2:12 pm
Division: Grad
State: NY

Re: Mousetrap Vehicle B

Postby Gemma W » January 2nd, 2012, 12:07 pm

There is no rule about what material to use for the car, right?
No, the rules do not specify a material, except for the fixed point which must be a paperclip.

Also, do people suggest to make the car with an adjustable mechanism to allow for calibration, or to make it fixed and eliminate inconsistencies?
2015 events: WIDI, Protein Modeling, Geomapping, Chem Lab

2014 events: WIDI, Geomapping, Materials Science, Food Science
2013 events: WIDI, Mousetrap Vehicle, Heredity, Food Science, Metric Mastery

Best ever place: Nationals, 3rd in WIDI

User avatar
illusionist
Member
Member
Posts: 942
Joined: March 20th, 2010, 4:13 pm
Division: C
State: MI

Re: Mousetrap Vehicle B

Postby illusionist » January 2nd, 2012, 12:50 pm

My choice has always been to include some sort of a steering mechanism in the car. You may build the vehicle so that it will travel perfectly straight, but overtime it will be altered. A fixed body/axle doesn't allow for adjustment or correction later on.
2012-2013 Building Event Captain
Rule 7d. "Event Supervisors are allowed to break any competitors' devices" -bearasauras

Gemma W
Member
Member
Posts: 196
Joined: March 10th, 2011, 2:12 pm
Division: Grad
State: NY

Re: Mousetrap Vehicle B

Postby Gemma W » January 9th, 2012, 12:10 pm

Thanks. We decided on a mechanism that will allow for slight changes in the axle's angle.
2015 events: WIDI, Protein Modeling, Geomapping, Chem Lab

2014 events: WIDI, Geomapping, Materials Science, Food Science
2013 events: WIDI, Mousetrap Vehicle, Heredity, Food Science, Metric Mastery

Best ever place: Nationals, 3rd in WIDI

User avatar
mousetrapfury
Member
Member
Posts: 10
Joined: November 29th, 2011, 12:48 pm
Division: B
State: NC

Re: Mousetrap Vehicle B

Postby mousetrapfury » January 10th, 2012, 2:01 pm

What should you use other than sauter to attach the rod with the string to the mousetrap?

User avatar
illusionist
Member
Member
Posts: 942
Joined: March 20th, 2010, 4:13 pm
Division: C
State: MI

Re: Mousetrap Vehicle B

Postby illusionist » January 10th, 2012, 3:45 pm

What should you use other than sauter to attach the rod with the string to the mousetrap?
That's called a Pull Arm. The easiest way is to simply zip-tie it to the mousetrap and then maybe reinforce with hot glue. This is rather robust and also allows for easy removal if necessary.
2012-2013 Building Event Captain
Rule 7d. "Event Supervisors are allowed to break any competitors' devices" -bearasauras

Pauly_Rocks
Member
Member
Posts: 13
Joined: January 10th, 2012, 12:34 pm
Division: B
State: MA

Re: Mousetrap Vehicle B

Postby Pauly_Rocks » January 10th, 2012, 6:47 pm

What should you use other than sauter to attach the rod with the string to the mousetrap?
That's called a Pull Arm. The easiest way is to simply zip-tie it to the mousetrap and then maybe reinforce with hot glue. This is rather robust and also allows for easy removal if necessary.
I'm using some clamps...not exactly sure what they're called but they're U-shaped and then they go through some sort of holding device and are attached with washers... I used them to clamp the rod onto the arm of the mousetrap... I'll find out the name of the clamps, sorry I didn't know! :(
Been there.
Done that.

Events I've been on: Elevated Bridge (1 yr.), Ornithology (2 yr.), Battery Buggy (2 yr.), Optics (2 yr.), Mousetrap Vehicle (1 yr.), Awesome Aquifers (1 yr.)

Rawr.

chalker
Member
Member
Posts: 2090
Joined: January 9th, 2009, 7:30 pm
Division: Grad
State: OH

Re: Mousetrap Vehicle B

Postby chalker » January 10th, 2012, 8:04 pm

What should you use other than sauter to attach the rod with the string to the mousetrap?
That's called a Pull Arm. The easiest way is to simply zip-tie it to the mousetrap and then maybe reinforce with hot glue. This is rather robust and also allows for easy removal if necessary.
I'm using some clamps...not exactly sure what they're called but they're U-shaped and then they go through some sort of holding device and are attached with washers... I used them to clamp the rod onto the arm of the mousetrap... I'll find out the name of the clamps, sorry I didn't know! :(
You might also want to look at hose clamps: http://en.wikipedia.org/wiki/Hose_clamp

Student Alumni
National Event Supervisor
National Physical Sciences Rules Committee Chair

Pauly_Rocks
Member
Member
Posts: 13
Joined: January 10th, 2012, 12:34 pm
Division: B
State: MA

Re: Mousetrap Vehicle B

Postby Pauly_Rocks » January 11th, 2012, 1:18 pm

You might also want to look at hose clamps: http://en.wikipedia.org/wiki/Hose_clamp
Yeah. those work well too. :)
Been there.
Done that.

Events I've been on: Elevated Bridge (1 yr.), Ornithology (2 yr.), Battery Buggy (2 yr.), Optics (2 yr.), Mousetrap Vehicle (1 yr.), Awesome Aquifers (1 yr.)

Rawr.


Return to “2012 Build Events”

Who is online

Users browsing this forum: No registered users and 1 guest