Dowel Height?

Locked
Orion66
Member
Member
Posts: 20
Joined: January 10th, 2017, 4:46 pm
Division: C
State: GA
Has thanked: 0
Been thanked: 0

Dowel Height?

Post by Orion66 »

Very basic question:

There is no minimum height for the wooden dowel, right? I couldn't find any reference to one in the rules. Having always needed a ~20cm or so high dowel in the past for vehicle-based events, this feels kind of strange to me. Just looking to confirm that this is correct.
Chattahoochee High School

"Don't bother me. I'm busy conserving energy, momentum, and angular momentum"

2016: Bridges | Air Trajectory | Hydrogeology
2017: Towers | Helicopters | Hydrogeology
2018: Towers | Helicopters | Mousetrap Vehicle, Hovercraft
User avatar
dragonfruit35
Exalted Member
Exalted Member
Posts: 296
Joined: February 28th, 2015, 7:49 am
Division: Grad
State: VA
Pronouns: She/Her/Hers
Has thanked: 7 times
Been thanked: 1 time

Re: Dowel Height?

Post by dragonfruit35 »

Orion66 wrote:Very basic question:

There is no minimum height for the wooden dowel, right? I couldn't find any reference to one in the rules. Having always needed a ~20cm or so high dowel in the past for vehicle-based events, this feels kind of strange to me. Just looking to confirm that this is correct.
Right! I thought this was weird as well, but as it turns out the dowel just needs to be within 1cm of the floor and the height doesn't matter.
tjhsst '20
virginia tech '24
2x codebusters national medalist

"it's not a pen, it's a principle!" - annie edison
Otkrlj
Member
Member
Posts: 39
Joined: December 11th, 2017, 2:33 pm
Division: C
State: MO
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by Otkrlj »

Im really confused. The dowel has to be within a cm of the track? How do you do that?
2020 events: codebusters, towers, gravity vehicle, ping pong paracute 8-) 8-)
User avatar
JasperKota
Exalted Member
Exalted Member
Posts: 188
Joined: October 22nd, 2015, 8:01 pm
Division: C
State: NY
Has thanked: 2 times
Been thanked: 12 times

Re: Dowel Height?

Post by JasperKota »

Otkrlj wrote:Im really confused. The dowel has to be within a cm of the track? How do you do that?
Like stick the dowel somewhere on your vehicle (with glue, tape, whatever) so the bottom of the dowel, vertically, is less than 1 cm off the ground.
2020 Events: Fossils, Gravity Vehicle, Wright Stuff, Ping Pong Parachute
2019 Events: Fossils, Mousetrap Vehicle, Wright Stuff
2018 Events: Helicopters, Mousetrap Vehicle, Parasitology, WIDI
2017 Events: Ecology, Invasives, Wright Stuff
2016 Events: Crave the Wave, Dynamic Planet, Invasives
Otkrlj
Member
Member
Posts: 39
Joined: December 11th, 2017, 2:33 pm
Division: C
State: MO
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by Otkrlj »

Ok thanks
2020 events: codebusters, towers, gravity vehicle, ping pong paracute 8-) 8-)
madeline.hartlage
Member
Member
Posts: 1
Joined: January 14th, 2018, 12:16 pm
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by madeline.hartlage »

Don't understand how to comply with 1cm from track and perpendicular to track rules. Seems like the mouse traps would then need to be around 1cm from floor?
Otkrlj
Member
Member
Posts: 39
Joined: December 11th, 2017, 2:33 pm
Division: C
State: MO
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by Otkrlj »

madeline.hartlage wrote:Don't understand how to comply with 1cm from track and perpendicular to track rules. Seems like the mouse traps would then need to be around 1cm from floor?
We are seporating our mousetraps and putting the dowel through the gap so it will be 1cm off the ground when the dowel is perpendicular to the floor
2020 events: codebusters, towers, gravity vehicle, ping pong paracute 8-) 8-)
User avatar
antoine_ego
Exalted Member
Exalted Member
Posts: 387
Joined: May 24th, 2016, 5:37 pm
Division: Grad
State: MA
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by antoine_ego »

Otkrlj wrote:
madeline.hartlage wrote:Don't understand how to comply with 1cm from track and perpendicular to track rules. Seems like the mouse traps would then need to be around 1cm from floor?
We are seporating our mousetraps and putting the dowel through the gap so it will be 1cm off the ground when the dowel is perpendicular to the floor
Will the dowel be touching the cup as it pushes it along?
Rest in Peace Len Joeris
[b]2016 Air Trajectory Nationals - 3rd
2018 Hovercraft Nationals - 6th
2018 Mousetrap Nationals - 6th
2018 Nationals - Team 9th Place!
2019 Astronomy Nationals - 3rd!
2019 Nationals - Team 9th Place!
[/b]
Acton-Boxborough Regional High School Captain 17-19
Otkrlj
Member
Member
Posts: 39
Joined: December 11th, 2017, 2:33 pm
Division: C
State: MO
Has thanked: 0
Been thanked: 0

Re: Dowel Height?

Post by Otkrlj »

Ya the dowel will be touching the cup at the start
2020 events: codebusters, towers, gravity vehicle, ping pong paracute 8-) 8-)
Locked

Return to “Mousetrap Vehicle C”

Who is online

Users browsing this forum: No registered users and 1 guest