Mousetrap Vehicle C

DarthBuilder
Member
Member
Posts: 288
Joined: August 1st, 2017, 8:02 am
Division: Grad
State: IL

Re: Mousetrap Vehicle C

Postby DarthBuilder » January 19th, 2019, 9:40 am

During competition are we allowed to put down a protractor on the starting point then before we start our vehicle can we remove it? The last two competitions were pretty confused too but they did let us as long as we removed it before our first and second runs.
Deleted

sciencecat42
Member
Member
Posts: 74
Joined: March 14th, 2016, 7:07 pm
State: -

Re: Mousetrap Vehicle C

Postby sciencecat42 » January 19th, 2019, 10:23 am

Handheld rotary tools and lathe by themselves are not safe methods for cutting carbon fiber; both would disperse fine abrasive glass-like fibers that can easily accumulate in your lungs and irritate your respiratory tract. These fibers are also electrically conductive and can damage electronics.

If you decide you must use carbon fiber in your device, consider designing your vehicle around the dimensions of stock carbon fiber so you can avoid cutting. If you want threads, consider attaching a component that has threads rather than modifying the carbon fiber. And if you decide you must cut carbon fiber, process it wet, e.g. in a liquid bath, and dispose of your waste properly. Please read about carbon fiber safety before using it.

https://www.rhinocarbonfiber.com/carbon-safety/

http://www.fullforcerc.com/carbon-care/

https://www.tapplastics.com/uploads/pdf ... 0Sheet.pdf
So it sounds like people aren't actually using CF for their axles? Or maybe they use an unthreaded rod for the back and a non-CF threaded rod in front.

sciencecat42
Member
Member
Posts: 74
Joined: March 14th, 2016, 7:07 pm
State: -

Re: Mousetrap Vehicle C

Postby sciencecat42 » January 23rd, 2019, 5:46 pm

Anyone finding an issue with their wing nut not winding that far on the brake axle? Is this even an issue?

User avatar
dragonfruit35
Exalted Member
Exalted Member
Posts: 279
Joined: February 28th, 2015, 7:49 am
Division: C
State: VA
Location: TJHSST

Re: Mousetrap Vehicle C

Postby dragonfruit35 » January 23rd, 2019, 6:22 pm

Anyone finding an issue with their wing nut not winding that far on the brake axle? Is this even an issue?
What do you mean by that? Is it just not traveling very far? If so, you might want to find one with a lower thread count per inch so that the wingnut travels further over the same vehicle travel distance.
(VT/FFX/Reg/States/Nats)
MV 1/1/5/-/- Mission 3/4/4/-/- Herp 7/2/4/-/-
WiFi -/-/-/4/13  Indoor Bottle Rocket -/-/-/1/- Code -/-/-/-/1
(Duke/Reg/Cornell/States/Nats)
MV 2/3/7/3/10 Mission 3/7/- Sounds 4/2/- Code 3/1/1/1/5 Herp -/-/11/1/26
[/color]
Goooooooo Colonials!!!

sciencecat42
Member
Member
Posts: 74
Joined: March 14th, 2016, 7:07 pm
State: -

Re: Mousetrap Vehicle C

Postby sciencecat42 » January 23rd, 2019, 8:38 pm

Anyone finding an issue with their wing nut not winding that far on the brake axle? Is this even an issue?
What do you mean by that? Is it just not traveling very far? If so, you might want to find one with a lower thread count per inch so that the wingnut travels further over the same vehicle travel distance.
Yeah it only travels about a fifth of the length of the rod. I'm not sure if this is even an issue though. Wouldn't it be more precise?

User avatar
dragonfruit35
Exalted Member
Exalted Member
Posts: 279
Joined: February 28th, 2015, 7:49 am
Division: C
State: VA
Location: TJHSST

Re: Mousetrap Vehicle C

Postby dragonfruit35 » January 23rd, 2019, 10:38 pm

Anyone finding an issue with their wing nut not winding that far on the brake axle? Is this even an issue?
What do you mean by that? Is it just not traveling very far? If so, you might want to find one with a lower thread count per inch so that the wingnut travels further over the same vehicle travel distance.
Yeah it only travels about a fifth of the length of the rod. I'm not sure if this is even an issue though. Wouldn't it be more precise?
It’s not necessarily an issue. It depends on whether you’re determining your brake setting just by looking at it, in which case it would be advantageous to use a lower thread count because the marks will be more spaced out. Otherwise, there shouldn’t be any effect on the braking precision.
(VT/FFX/Reg/States/Nats)
MV 1/1/5/-/- Mission 3/4/4/-/- Herp 7/2/4/-/-
WiFi -/-/-/4/13  Indoor Bottle Rocket -/-/-/1/- Code -/-/-/-/1
(Duke/Reg/Cornell/States/Nats)
MV 2/3/7/3/10 Mission 3/7/- Sounds 4/2/- Code 3/1/1/1/5 Herp -/-/11/1/26
[/color]
Goooooooo Colonials!!!

TheGhghp
Member
Member
Posts: 5
Joined: January 16th, 2019, 9:23 pm

Re: Mousetrap Vehicle C

Postby TheGhghp » January 27th, 2019, 11:27 am

What size braided fishing line have you guys been using? I'm thinking of buying a 0.1mm diameter line with strength up to 8lb, but I'm not sure if I should go for something thicker.

4Head
Member
Member
Posts: 237
Joined: November 14th, 2016, 11:29 am
Division: C
State: -

Re: Mousetrap Vehicle C

Postby 4Head » January 27th, 2019, 12:27 pm

What size braided fishing line have you guys been using? I'm thinking of buying a 0.1mm diameter line with strength up to 8lb, but I'm not sure if I should go for something thicker.
that'll be strong enough, just very hard to work with
2019 Sounds of Music National Champion

User avatar
Things2do
Member
Member
Posts: 124
Joined: February 12th, 2018, 2:30 pm
Division: C
State: TN
Location: Unfortunately, not Utah somewhere near the Colorado border

Re: Mousetrap Vehicle C

Postby Things2do » January 27th, 2019, 1:08 pm

What size braided fishing line have you guys been using? I'm thinking of buying a 0.1mm diameter line with strength up to 8lb, but I'm not sure if I should go for something thicker.
that'll be strong enough, just very hard to work with
I'm using Kevlar fishing line. It's 50 lb test, I think... It's a little hard to tie a small loop in it without leaving a long running end, but it lasts quite a while.
John 5:46-47
When your signature exceeds the allotted 300 characters, you put it here...
Is this where I put the Builder Cult?
"I think that we're all mentally ill. Those of us outside the asylums only hide it a little better - and maybe not all that much better after all." - Stephen King

4build
Member
Member
Posts: 1
Joined: January 27th, 2019, 3:30 pm

Re: Mousetrap Vehicle C

Postby 4build » January 27th, 2019, 3:32 pm

What material are people using for the drive arms of their vehicle? We're currently using balsa wood but it's flexing a lot.


Return to “Mousetrap Vehicle C”

Who is online

Users browsing this forum: No registered users and 1 guest