Wright Stuff C

bjt4888
Member
Member
Posts: 483
Joined: June 16th, 2013, 12:35 pm
Division: C
State: MI

Re: Wright Stuff C

Postby bjt4888 » February 1st, 2019, 7:33 pm

I have three workstations in my shop, so my schools build three airplanes in mostly one 8-hour day (usually a Saturday 9 am till 5 pm) with a couple more hours on another evening for finishing details. The three airplanes are two for the school’s A-Team and one for the B-Team. The B-Team returns on another day to build their spare.

Of course, there are other build sessions for additional variations in the airplane setup.

So far this year, my four schools have constructed 15 airplanes. It’s been a busy year.

Brian T

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 2nd, 2019, 8:23 am

geniusjohn5 wrote:Survey: how long did it take YOU to build your first plane?

this season lmao like 2 weeks cause we didnt have all our supplies yet
first year (7th grade) uhhh like around 2-3 weeks cause i literally had no clue what i was doing
this season but like our first actual plane like 1 week maybe even less and i mean it was good enough to not bomb so yay
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

geniusjohn5
Member
Member
Posts: 110
Joined: January 18th, 2017, 6:57 pm
Division: C
State: -

Re: Wright Stuff C

Postby geniusjohn5 » February 2nd, 2019, 7:26 pm

Does anybody know of a durable PORTABLE platform where I can tape down the full-sized drawing to? I need to transport the Wright Stuff kit back and forth between my partner and I. Would a large (but thin) piece of a cardboard work?
The biologist speculates, "What's the meaning of life?"
The physicist asks, "In the universe, does matter really matter?"
The chemist replies, "I shall find solutions to both questions."

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 2nd, 2019, 7:30 pm

geniusjohn5 wrote:Does anybody know of a durable PORTABLE platform where I can tape down the full-sized drawing to? I need to transport the Wright Stuff kit back and forth between my partner and I. Would a large (but thin) piece of a cardboard work?

get foam board spray glue the design to it and cover in wax paper. that way u can also use pins to hold stuff down and get glue on it w/o ruining anything. also photocopy the template if ya can
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

newflight
Member
Member
Posts: 17
Joined: February 2nd, 2019, 8:48 pm

Re: Wright Stuff C

Postby newflight » February 2nd, 2019, 8:57 pm

I recently ran into an issue with nose down at initial launch with higher torque. I wind rubber band to 1.3 torque and then dewind it to 0.65 torque. When I released it, it will hit on floor after several seconds. Then I picked it up and launched it again, it will fly more than 2 minutes. I then do the same thing to wind torque to 1.3 and dewind it to 0.6. it will fly ok. so, why it cannot fly with higher initial launch torque?

Rossyspsce
Member
Member
Posts: 180
Joined: June 3rd, 2018, 5:32 pm
State: -

Re: Wright Stuff C

Postby Rossyspsce » February 2nd, 2019, 9:30 pm

I was wondering where you guys bought rubber from?

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 3rd, 2019, 7:36 am

newflight wrote:I recently ran into an issue with nose down at initial launch with higher torque. I wind rubber band to 1.3 torque and then dewind it to 0.65 torque. When I released it, it will hit on floor after several seconds. Then I picked it up and launched it again, it will fly more than 2 minutes. I then do the same thing to wind torque to 1.3 and dewind it to 0.6. it will fly ok. so, why it cannot fly with higher initial launch torque?


wait so youre winding to 1.3 and then winding backwards to .65 or are you releasing and then letting go so the launch torque is .65
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 3rd, 2019, 7:38 am

Rossyspsce wrote:I was wondering where you guys bought rubber from?

fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

User avatar
CrayolaCrayon
Member
Member
Posts: 192
Joined: October 25th, 2017, 8:24 am
Division: C
State: PA
Contact:

Re: Wright Stuff C

Postby CrayolaCrayon » February 3rd, 2019, 7:54 am

newflight wrote:I recently ran into an issue with nose down at initial launch with higher torque. I wind rubber band to 1.3 torque and then dewind it to 0.65 torque. When I released it, it will hit on floor after several seconds. Then I picked it up and launched it again, it will fly more than 2 minutes. I then do the same thing to wind torque to 1.3 and dewind it to 0.6. it will fly ok. so, why it cannot fly with higher initial launch torque?


I know I had an issue like that once where the prop was angled downwards ever so slightly, and it fought against the lift at the beginning because of the high torque, which made it dive. There might be something more behind your issue, however.
Wright Stuff National Runner-up 2019

F1D is fun if nothing is breaking

jander14indoor
Member
Member
Posts: 1540
Joined: April 30th, 2007, 7:54 am
State: -

Re: Wright Stuff C

Postby jander14indoor » February 3rd, 2019, 8:29 am

Most likely your fuselage is bending at the higher torques. Pulls the nose down increasing town thrust, and tail down, causing excess nose down moment.

Jeff Anderson
Livonia, MI

Rossyspsce
Member
Member
Posts: 180
Joined: June 3rd, 2018, 5:32 pm
State: -

Re: Wright Stuff C

Postby Rossyspsce » February 3rd, 2019, 9:08 am

klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?

fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai


Do you mind dropping a link, I've only gotten results for volare?

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 3rd, 2019, 9:20 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?

fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai


Do you mind dropping a link, I've only gotten results for volare?

yea sure
on here u can get other kinds but i attached one that you may be interesting in. warning you'll need a rubber stripper if you purchase this
https://www.faimodelsupply.com/product/ ... rt-rubber/
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

User avatar
CrayolaCrayon
Member
Member
Posts: 192
Joined: October 25th, 2017, 8:24 am
Division: C
State: PA
Contact:

Re: Wright Stuff C

Postby CrayolaCrayon » February 3rd, 2019, 9:20 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?

fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai


Do you mind dropping a link, I've only gotten results for volare?

https://www.faimodelsupply.com/product- ... rt-rubber/
Wright Stuff National Runner-up 2019

F1D is fun if nothing is breaking

User avatar
klastyioer
Member
Member
Posts: 360
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: Wright Stuff C

Postby klastyioer » February 3rd, 2019, 9:23 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?

fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai


Do you mind dropping a link, I've only gotten results for volare?

honestly buy whatever size and amount u want
honestly, it's not about the medals. go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.
-
Builder Cult >:)

'17 - Towers, Wright Stuff, rocks
'18 - Towers, Wright Stuff, Mystery Arch, road
'19 - Wright Stuff

Rossyspsce
Member
Member
Posts: 180
Joined: June 3rd, 2018, 5:32 pm
State: -

Re: Wright Stuff C

Postby Rossyspsce » February 3rd, 2019, 9:33 am

klastyioer wrote:
Rossyspsce wrote:
klastyioer wrote:fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai


Do you mind dropping a link, I've only gotten results for volare?

yea sure
on here u can get other kinds but i attached one that you may be interesting in. warning you'll need a rubber stripper if you purchase this
https://www.faimodelsupply.com/product/ ... rt-rubber/


For the rubber stripper part, is this true for all rubber that comes in box?

Edit: for example the description of this rubber is 3/32" so I would assume that it comes precut into a 3/32" strand? https://www.faimodelsupply.com/product/ ... rt-rubber/


Return to “Wright Stuff C”

Who is online

Users browsing this forum: No registered users and 4 guests