You could also try particleboard. It's just really bendy wood.SluffAndRuff wrote: ↑November 30th, 2019, 5:18 pm What's a good thickness for the sheet metal to build the ramp out of - something that's thin enough to work with easily but not too thin to be weak? Thanks!
Ramp Creation
- Tendan
- Member
- Posts: 63
- Joined: January 27th, 2019, 5:37 pm
- Division: C
- State: PA
- Has thanked: 5 times
- Been thanked: 0
Re: Ramp Creation
2019 - 2020 Events
~ Boomilever
~ Detector Building
~ Gravity Vehicle
~ Machines
~ Ping-Pong Parachute
~ Boomilever
~ Detector Building
~ Gravity Vehicle
~ Machines
~ Ping-Pong Parachute
- sciolyperson1
- Exalted Member
- Posts: 1074
- Joined: April 23rd, 2018, 7:13 pm
- Division: C
- State: NJ
- Pronouns: He/Him/His
- Has thanked: 529 times
- Been thanked: 601 times
- Contact:
Re: Ramp Creation
According to the rules and code of ethics, "One or more of a 15-member team must have constructed all pre-built devices presented for judging." Personally I don't think you would be able to, as after you impound you can't put it back in the impound area for your 2nd team to compete.
SoCal Planning Team & BirdSO Tournament Director
WW-P HSN '22, Community MS '18
Sciolyperson1's Userpage
WW-P HSN '22, Community MS '18
Sciolyperson1's Userpage
- Tendan
- Member
- Posts: 63
- Joined: January 27th, 2019, 5:37 pm
- Division: C
- State: PA
- Has thanked: 5 times
- Been thanked: 0
Re: Ramp Creation
As we just found out at LISO, each team must have their own ramp. They allowed us to compete all of our cars with one ramp, but I doubt a supervisor will let it slide again.
2019 - 2020 Events
~ Boomilever
~ Detector Building
~ Gravity Vehicle
~ Machines
~ Ping-Pong Parachute
~ Boomilever
~ Detector Building
~ Gravity Vehicle
~ Machines
~ Ping-Pong Parachute
-
- Member
- Posts: 62
- Joined: February 18th, 2019, 2:18 pm
- Division: C
- State: FL
- Has thanked: 2 times
- Been thanked: 1 time
Re: Ramp Creation
Yeah that does not sound legal.
I build. A lot.
Boca Raton High School.
Events: Boomi, Gravity Vehicle, Wright Stuff.
Incomplete Userpage
Boca Raton High School.
Events: Boomi, Gravity Vehicle, Wright Stuff.
Incomplete Userpage
- MTV<=>Operator
- Member
- Posts: 142
- Joined: February 8th, 2019, 12:41 pm
- Division: Grad
- State: NY
- Has thanked: 9 times
- Been thanked: 4 times
Re: Ramp Creation
How is everyone attaching the sheet metal surface to the plywood sides? Would I be able to just drill through the sheet metal into the plywood to hold it down, or is there more involved in the attachment process? Also, is 1/16" a good thickness to use? Thanks.
THHS '21 Builder Cult Member
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
- CPScienceDude
- Exalted Member
- Posts: 374
- Joined: December 12th, 2018, 2:40 pm
- Division: Grad
- State: IN
- Pronouns: He/Him/His
- Has thanked: 144 times
- Been thanked: 91 times
Re: Ramp Creation
I used 1/16 and it's working well. I used sheet metal screws to screw through the sheet metal and into the wood frame.MTV<=>Operator wrote: ↑December 11th, 2019, 7:10 pm How is everyone attaching the sheet metal surface to the plywood sides? Would I be able to just drill through the sheet metal into the plywood to hold it down, or is there more involved in the attachment process? Also, is 1/16" a good thickness to use? Thanks.
- MTV<=>Operator
- Member
- Posts: 142
- Joined: February 8th, 2019, 12:41 pm
- Division: Grad
- State: NY
- Has thanked: 9 times
- Been thanked: 4 times
Re: Ramp Creation
Ok, thank you. Would 1/2 in be adequate thickness for the plywood?CPScienceDude wrote: ↑December 11th, 2019, 7:19 pmI used 1/16 and it's working well. I used sheet metal screws to screw through the sheet metal and into the wood frame.MTV<=>Operator wrote: ↑December 11th, 2019, 7:10 pm How is everyone attaching the sheet metal surface to the plywood sides? Would I be able to just drill through the sheet metal into the plywood to hold it down, or is there more involved in the attachment process? Also, is 1/16" a good thickness to use? Thanks.
THHS '21 Builder Cult Member
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
- CPScienceDude
- Exalted Member
- Posts: 374
- Joined: December 12th, 2018, 2:40 pm
- Division: Grad
- State: IN
- Pronouns: He/Him/His
- Has thanked: 144 times
- Been thanked: 91 times
Re: Ramp Creation
That's what mine is, be careful when screwing the sheet metal onto the plywood, cause it started to split for me.MTV<=>Operator wrote: ↑December 11th, 2019, 7:33 pmOk, thank you. Would 1/2 in be adequate thickness for the plywood?CPScienceDude wrote: ↑December 11th, 2019, 7:19 pmI used 1/16 and it's working well. I used sheet metal screws to screw through the sheet metal and into the wood frame.MTV<=>Operator wrote: ↑December 11th, 2019, 7:10 pm How is everyone attaching the sheet metal surface to the plywood sides? Would I be able to just drill through the sheet metal into the plywood to hold it down, or is there more involved in the attachment process? Also, is 1/16" a good thickness to use? Thanks.
- MTV<=>Operator
- Member
- Posts: 142
- Joined: February 8th, 2019, 12:41 pm
- Division: Grad
- State: NY
- Has thanked: 9 times
- Been thanked: 4 times
Re: Ramp Creation
Ok. Thanks for the help!
THHS '21 Builder Cult Member
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 NYC), Detector (8 YUSO, 7 NYC), WS (10 NYC), PPP
2020-2021 Events/ Yosemite/HUSO/River Hill/ NYC South Regional
Vehicle Design / 1/--/--/--
WICI / 3/--/--/--
Circuits /--/ 3/ 5/ 1
Machines /--/ 4/ 2/ 2
Detector /--/--/ 2/--
Who is online
Users browsing this forum: No registered users and 4 guests