Ramp Creation

User avatar
MTV<=>Operator
Member
Member
Posts: 138
Joined: February 8th, 2019, 12:41 pm
Division: C
State: NY
Has thanked: 8 times
Been thanked: 4 times

Re: Ramp Creation

Post by MTV<=>Operator » December 18th, 2019, 5:21 pm

Did you have to use anything to bend the 1/6 in sheet metal or were you able to just press it against the ramp profile and drill it down?
THHS '21 Builder Cult Member
2017-2018
2018-2019
2019-2020: GV (9 YUSO, 5 Regional), Detector (8 YUSO, 7 Regional), WS (10 Regional), PPP
2020-2021 Events/ Yosemite
Vehicle Design / 1
WICI / 3
Circuits /--
Machines /--

User avatar
CPScienceDude
Exalted Member
Exalted Member
Posts: 354
Joined: December 12th, 2018, 2:40 pm
Division: C
State: IN
Pronouns: He/Him/His
Has thanked: 139 times
Been thanked: 80 times

Re: Ramp Creation

Post by CPScienceDude » December 18th, 2019, 6:36 pm

MTV<=>Operator wrote:
December 18th, 2019, 5:21 pm
Did you have to use anything to bend the 1/6 in sheet metal or were you able to just press it against the ramp profile and drill it down?
I just pressed it down and drilled it
Captain of CPSO

Assassinator 139 and 147
2021 events: Astronomy, Chem Lab, Ornithology, Machines, Gravity Vehicle, and Forensics

About Me!
Image

rayner
Member
Member
Posts: 12
Joined: September 17th, 2019, 6:14 pm
Has thanked: 0
Been thanked: 0

Re: Ramp Creation

Post by rayner » December 23rd, 2019, 7:13 pm

Am I understanding this correctly? People are using plywood for the ramp surface and then covering it with a layer of sheet metal? So the wood is for shape/rigidity and the sheet metal is for smoothness?

akso21
Member
Member
Posts: 1
Joined: December 30th, 2019, 3:45 pm
Division: C
State: NC
Has thanked: 0
Been thanked: 0

Re: Ramp Creation

Post by akso21 » December 30th, 2019, 3:48 pm

rayner wrote:
December 23rd, 2019, 7:13 pm
Am I understanding this correctly? People are using plywood for the ramp surface and then covering it with a layer of sheet metal? So the wood is for shape/rigidity and the sheet metal is for smoothness?
Yeah, that's probably the easiest way to get a pretty decent ramp. Personally, I am going for polycarbonate instead of sheet metal gets the job done as well.

Airco2020
Member
Member
Posts: 117
Joined: February 11th, 2019, 12:43 pm
Has thanked: 0
Been thanked: 1 time

Re: Ramp Creation

Post by Airco2020 » December 31st, 2019, 8:41 am

rayner wrote:
December 23rd, 2019, 7:13 pm
Am I understanding this correctly? People are using plywood for the ramp surface and then covering it with a layer of sheet metal? So the wood is for shape/rigidity and the sheet metal is for smoothness?
No reason for plywood and sheet metal as the ramp surface. Plywood sides and either sheet metal or thin, 1/4" luan type plywood for the surface.

petal
Member
Member
Posts: 7
Joined: October 27th, 2018, 5:22 pm
Has thanked: 0
Been thanked: 0

Re: Ramp Creation

Post by petal » January 19th, 2020, 7:00 pm

My car keeps bouncing—the wheels lift off the ground a few centimeters—as it leaves the bottom of the ramp, in the transition from ramp to floor. I believe that this may because the curve on my ramp is too steep. Does anyone have any experience with this? Do you recommend just rebuilding the ramp (there’s no way for us to change the curve of the current ramp because everything is glued into place)? Are they any changes that we could potentially make to the car to eliminate the problem instead? We tried putting extra weight on the car in hopes that that would prevent the bouncing, but it has been to no avail.

knightmoves
Member
Member
Posts: 318
Joined: April 26th, 2018, 6:40 pm
Has thanked: 2 times
Been thanked: 27 times

Re: Ramp Creation

Post by knightmoves » January 19th, 2020, 7:28 pm

petal wrote:
January 19th, 2020, 7:00 pm
My car keeps bouncing—the wheels lift off the ground a few centimeters—as it leaves the bottom of the ramp, in the transition from ramp to floor. I believe that this may because the curve on my ramp is too steep. Does anyone have any experience with this? Do you recommend just rebuilding the ramp (there’s no way for us to change the curve of the current ramp because everything is glued into place)? Are they any changes that we could potentially make to the car to eliminate the problem instead? We tried putting extra weight on the car in hopes that that would prevent the bouncing, but it has been to no avail.
It sounds like you may have an abrupt transition between the ramp and the floor. In other words, your ramp is too steep where it meets the floor. If you don't want to change your ramp, you might have success with larger diameter wheels.

Airco2020
Member
Member
Posts: 117
Joined: February 11th, 2019, 12:43 pm
Has thanked: 0
Been thanked: 1 time

Re: Ramp Creation

Post by Airco2020 » January 20th, 2020, 8:09 pm

petal wrote:
January 19th, 2020, 7:00 pm
My car keeps bouncing—the wheels lift off the ground a few centimeters—as it leaves the bottom of the ramp, in the transition from ramp to floor. I believe that this may because the curve on my ramp is too steep. Does anyone have any experience with this? Do you recommend just rebuilding the ramp (there’s no way for us to change the curve of the current ramp because everything is glued into place)? Are they any changes that we could potentially make to the car to eliminate the problem instead? We tried putting extra weight on the car in hopes that that would prevent the bouncing, but it has been to no avail.
Just rebuilt ours for the same problem 😡. I thought about try to put some shock absorbing solution in the car but in the end it was easier to rebuild our ramp.

sdececco
Member
Member
Posts: 9
Joined: January 17th, 2019, 9:01 am
Division: C
State: PA
Has thanked: 0
Been thanked: 0

Re: Ramp Creation

Post by sdececco » January 27th, 2020, 5:22 am

095067 wrote:
December 6th, 2019, 1:32 pm
Hello, is one ramp allowed for all the teams of one school?
Look at the rules clarification. They state the answer there

brookeklynn
Member
Member
Posts: 4
Joined: March 26th, 2020, 11:24 am
Division: C
State: ND
Has thanked: 0
Been thanked: 1 time

Re: Ramp Creation

Post by brookeklynn » March 26th, 2020, 11:37 am

I think the hardest part of creating the ramp was figuring out what would excel the vehicle the farthest. The plan was to make a tall ramp with a steep incline to hopefully speed up the car using its own mass. The one big issue we ran into was what material to use for the ramp, we decided to use sheet metal. The issue of using sheet metal was cutting it. We got it figured out with the help of teachers, but without it would've been very difficult. I love the science olympiad because of the community and working with my friends.

Locked

Return to “Gravity Vehicle C”

Who is online

Users browsing this forum: No registered users and 1 guest