Fan Step

Locked
Zsharma
Member
Member
Posts: 7
Joined: March 4th, 2007, 4:47 pm
Has thanked: 0
Been thanked: 0

Fan Step

Post by Zsharma » April 1st, 2010, 11:51 pm

On my box I have all of the tasks working except the fan.... What I am having it do is blow a sheet of tinfoil off of the strips of metal to disconnect the electromagnet. First problem is, it's not reliable enough this way, like the tinfoil won't always make the connection. Second problem is the tinfoil doesn't give me enough current to power the electromagnet. And then the third problem is, when my mousetrap goes it might move it off the metal strips!! So, yeah what are all you guys using for this step?

BTW I'm using a fairly powerful computer fan. :geek:
2010 placement (CHS tournament, Aviation, Regionals, State)
Physics Lab 1st, 1st, 1st, 9th
It's About Time 1st, 1st, 2nd, N/A
Mission Possible 1st, 1st, 9th, 3rd

Balsa Man
Coach
Coach
Posts: 1318
Joined: November 13th, 2008, 3:01 am
Division: C
State: CO
Has thanked: 0
Been thanked: 3 times

Re: Fan Step

Post by Balsa Man » April 2nd, 2010, 4:16 am

Here's one way-
Use a piece of brass rod - we're using 3/32nd - 1/8th would be ok, too. Mount the fan up near the top of the box. The rod (initially) stands up vertically. Make a pivot at the bottom end. Put a ....paddle at the top end. That paddle goes in front of the fan. We're using a piece of 1/16th sheet balsa, about the size of the fan. Align the bottom so that the rod is just past vertical when the paddle is resting against the fan- that is, its leaning against the fan, just slightly. When the fan comes on, blows against the paddle. All it has to do is move it past vertical, then it falls on its own. For the electrical connection that the falling rod breaks, get some fairly thin brass sheet (Hobbytown), cut a couple strips, oh, 1/8th wide, couple inches long. Solder a wire to each. Set them up (we use a little block of balsa) so that the rod (when vertical) is between them - the strips aligned so that they are parallel to each other, with the distance between just a bit less than the diameter of the rod- so you get good contact without putting too much.....drag on the rod. Rod falls, breaks contact.....
Len Joeris
Fort Collins, CO

thepotato
Member
Member
Posts: 7
Joined: April 10th, 2010, 8:37 am
Division: C
Has thanked: 0
Been thanked: 0

Re: Fan Step

Post by thepotato » April 10th, 2010, 8:43 am

I used a computer fan as well. I had the fan on top of 2 1x1's. There was a piece of plywood resting on the ledge in front of the fan. The plywood was the size of the fan. It was duct taped down so it made a hinge with the ledge. When the fan blew, the wood swung down, hitting a wall switch.

cypressfalls Robert
Exalted Member
Exalted Member
Posts: 499
Joined: January 6th, 2009, 7:54 pm
Division: Grad
State: TX
Has thanked: 0
Been thanked: 0
Contact:

Re: Fan Step

Post by cypressfalls Robert » April 10th, 2010, 11:42 am

we just made a sail and put that on a car and ....

gh
Admin Emeritus
Admin Emeritus
Posts: 323
Joined: October 22nd, 2003, 5:47 pm
Division: Grad
State: NY
Has thanked: 0
Been thanked: 0
Contact:

Re: Fan Step

Post by gh » April 10th, 2010, 4:24 pm

Computer fans (99% of them) are generally not OK! They usually have brushless motors, which need a lot of illegal support circuitry.
“Rather fail with honor than succeed by fraud.” —Sophocles
If you are looking to give help or get help:
[wiki][/wiki] > Forum post > > PM > Email
Don't forget the Image Gallery, the , and the list of Exalted User medals.

cypressfalls Robert
Exalted Member
Exalted Member
Posts: 499
Joined: January 6th, 2009, 7:54 pm
Division: Grad
State: TX
Has thanked: 0
Been thanked: 0
Contact:

Re: Fan Step

Post by cypressfalls Robert » April 10th, 2010, 11:27 pm

gh wrote:Computer fans (99% of them) are generally not OK! They usually have brushless motors, which need a lot of illegal support circuitry.
we've bought two and none of them are powerfull enough for our wind needs...they suck

maggymay
Member
Member
Posts: 93
Joined: March 3rd, 2009, 4:24 pm
Division: C
Has thanked: 0
Been thanked: 0

Re: Fan Step

Post by maggymay » April 11th, 2010, 8:14 am

This one's giving us trouble too...ugh.

cypressfalls Robert
Exalted Member
Exalted Member
Posts: 499
Joined: January 6th, 2009, 7:54 pm
Division: Grad
State: TX
Has thanked: 0
Been thanked: 0
Contact:

Re: Fan Step

Post by cypressfalls Robert » April 11th, 2010, 8:51 am

to solve the whole power problem we put a wright stuff prop(propellor) on a motor and it works beastly

User avatar
Sir_L_Jenkins
Member
Member
Posts: 52
Joined: November 2nd, 2009, 2:40 pm
Division: C
State: IN
Has thanked: 0
Been thanked: 0
Contact:

Re: Fan Step

Post by Sir_L_Jenkins » April 17th, 2010, 8:25 am

cypressfalls Robert wrote: we've bought two and none of them are powerfull enough for our wind needs...they suck
Perhaps you should reverse the battery polarity so it blows the other way
*rimshot*
*Ahem*
Mentlegen.

Locked

Return to “Mission Possible C”

Who is online

Users browsing this forum: No registered users and 0 guests