Helicopter B/C [Trial]

Taran
Member
Member
Posts: 16
Joined: February 13th, 2010, 7:25 am
Division: B
State: IA

Re: Helicopter B/C [Trial]

Postby Taran » April 24th, 2010, 10:03 am

Is it possible to bend the balsa sheets to make a propeller? Otherwise it seems hard to make an efficient propeller.

----
Wright Stuff
Meteorology
Can't Judge A Powder

baker
Member
Member
Posts: 183
Joined: October 26th, 2005, 10:46 am
Division: C
State: NY
Location: Upstate NY

Re: Helicopter B/C [Trial]

Postby baker » April 24th, 2010, 10:21 am

Is it possible to bend the balsa sheets to make a propeller? Otherwise it seems hard to make an efficient propeller.

----
Wright Stuff
Meteorology
Can't Judge A Powder

Yes, cut out slightly larger the piece of balsa with the design of the prop. Soak in hot water for about an hour, place on form and hold with rubber bands. Let dry over night, cut out prop with razor blade or skizzors, can't spell scissors.. :D

OlympiadLover
Member
Member
Posts: 15
Joined: January 3rd, 2010, 8:42 pm
Division: C
State: NM

Re: Helicopter B/C [Trial]

Postby OlympiadLover » April 24th, 2010, 4:51 pm

How long should these last?
10' State: 1st: It's About Time and Experimental Design,, 2nd: Picture This, State, National team/UIUC
11' State: 1st: Experimental Design and 1st Wind Power, 3rd Mousetrap Vehicle, National team/UW-Madison
12' State: 3rd Thermodynamics, 3rd Water Quality, 8th Experimental Design, National team/UCF

baker
Member
Member
Posts: 183
Joined: October 26th, 2005, 10:46 am
Division: C
State: NY
Location: Upstate NY

Re: Helicopter B/C [Trial]

Postby baker » April 25th, 2010, 6:35 am

They'll hold up quite well, as good as any prop made of other materials. But, could be a little heavier than you might want. How long will they last? Until you hit the ceiling, the speakers, rafters, basket ball hoops, the wall, the uncontrolled dive into the floor...other than that, I'd say 15 seconds. We built ours with 1/32 material, props weight was just slightly less than 1 gram. We built a large, medium and small one. We let the stop watch tell us which was best.

SOCoach
Member
Member
Posts: 115
Joined: January 16th, 2003, 6:08 am

Re: Helicopter B/C [Trial]

Postby SOCoach » April 25th, 2010, 4:05 pm

Couple of questions for those in the know . . .

On the double prop design, the fixed rotor I am assuming by "fixed" it means it does not move right? It only spins as the motor stick spins . . is that correct?

Secondly, does anyone know how to make balsa props (the look like the ones used on penny planes)

cypressfalls Robert
Exalted Member
Exalted Member
Posts: 499
Joined: January 6th, 2009, 7:54 pm
Division: Grad
State: TX
Location: डार्क सब्रे के पीछे O.o
Contact:

Re: Helicopter B/C [Trial]

Postby cypressfalls Robert » April 25th, 2010, 4:13 pm

Couple of questions for those in the know . . .

On the double prop design, the fixed rotor I am assuming by "fixed" it means it does not move right? It only spins as the motor stick spins . . is that correct?
yes that is correct

baker
Member
Member
Posts: 183
Joined: October 26th, 2005, 10:46 am
Division: C
State: NY
Location: Upstate NY

Re: Helicopter B/C [Trial]

Postby baker » April 25th, 2010, 4:27 pm

This one show an outline of a home made propeller
http://www.indoorfreeflight.com/novice/dadnov.gif

Taran
Member
Member
Posts: 16
Joined: February 13th, 2010, 7:25 am
Division: B
State: IA

Re: Helicopter B/C [Trial]

Postby Taran » April 25th, 2010, 5:44 pm

Umm, I only see a Wright Stuff Design, or is it the thing at the bottom right?

----
Wright Stuff
Meteorology
Can't Judge A Powder

jander14indoor
Member
Member
Posts: 1560
Joined: April 30th, 2007, 7:54 am

Re: Helicopter B/C [Trial]

Postby jander14indoor » April 25th, 2010, 7:57 pm

Making lightweight indoor props from wood. OK, this is WAY more hardcore than you need in that the weight of this prop is 0.170 grams and your target is more like 0.8 to 1.0 gm per rotor. BUT, the processes and procedures can all be used to get an appropriately strong and heavy prop for SO Helicopter. See:
www.indoorduration.com/INAVHobbyShopper4.htm
www.indoorduration.com/INAVHobbyShopper5.htm

Use thicker wood, make it larger (40 cm or 16 inches vs 12 inches in that article), use denser wood, etc.

But, key point, PROCEDURE is correct in that it will result in fairly high efficiency, good working props or rotors.

Probably some other articles out there, look under EZB props or Penny Plane props.

Jeff Anderson
Livonia, MI

User avatar
chlorine kills
Member
Member
Posts: 8
Joined: October 16th, 2009, 8:01 pm
Division: B
State: TX
Location: let me think

Re: Helicopter B/C [Trial]

Postby chlorine kills » April 29th, 2010, 6:25 pm

FAIL my helicopter I built in 3 days won 5th at state

Robodude helped
Never trust a computer you can't throw out a window.
1st in optics at TX state.


Return to “2010 Build Events”

Who is online

Users browsing this forum: No registered users and 0 guests

cron