Hovercraft B/C

SPP SciO
Member
Member
Posts: 261
Joined: March 24th, 2015, 8:21 am
Division: B
State: NY
Location: Brooklyn

Re: Hovercraft B/C

Postby SPP SciO » October 10th, 2016, 11:38 am

Expanding on the point about "propellers must be shielded;" this rules presumably comes from MagLev. Not sure how long you've been around, but MagLev was basically scrapped due to safety issues. I believe chalker mentioned somewhere that Hovercraft is basically MagLev with the dangerous parts removed.
Oh yeah, for sure, it's a good rule. Even the computer fans with plastic blades are pretty dangerous. If you reach for one in a clumsy manner, you'll nick a finger. I do recall reading a story of gnarly MagLev incident; bleeding students can't make for "good optics" in the world of competitive science.
Coach
MS 821 Sunset Park Prep
http://www.sppscio.com

Wen
Member
Member
Posts: 9
Joined: October 9th, 2016, 10:03 pm

Re: Hovercraft B/C

Postby Wen » October 10th, 2016, 12:29 pm

Oh, it's more than that. They charge another $18+ shipping and $10+ tax. That is why I have been hesitating in ordering it. I also looked over the list. What I'm not sure about are Motor, Plastic Propeller, Axial Fan: what kind should I buy if I go buy them myself? Also Mesh Squares, what are they for? Wooden Dowels: Balsa wood? How thick? A design that shows what goes where will be helpful.
The motor is just a typical DC motor; the little metal cylinder with a shaft and two leads or wire tabs. Radio Shack sells them individually for $2-3 but if you ask the technology/science teachers at your school, they may just have a whole bin of them sitting around. The plastic propeller is literally nothing more than a twisted piece of plastic; you can buy multi packs online if you want to test out a variety, but they're also not hard to make - cut a strip of some thin rigid plastic, punch a hole through the middle with a hot nail, and if you warm it up over a flame for a few seconds you can twist it into a propeller shape. I believe the axial fan that comes with the kit is a small computer cooling fan. If you have no idea where to salvage one, check the links to DigiKey a few pages back in this thread. We wound up testing a few, and were able to find one that can lift the max weight for under $30 - but a smaller one, for much less than that, will do just fine. Mesh squares are for compliance with rule 4.e - the propellers must be shielded. Keep your eyes peeled and you'll find something lying around suitable for that (a pair of scissors may be needed). The dowel is for compliance with 4.g - 1/4" or more, for triggering the photogates. 1/4" is pretty standard "dowel size" so again, just look around for one, or pop in to the nearest dollar store.

As for how to put it altogether, you could probably reverse engineer it from the Ward's kit picture. Or, better yet, check out some of the videos on YouTube (there were links either in this thread or the Hovercraft thread in General Chat) and you'll see a hovercraft assembled from start to finish.
Thanks for the explanations/suggestions. Thanks to others for input too. I'm ready to get parts myself. It's a shame that I haven't built any of these. Will definitely have fun building them with kids:).

chalker
Member
Member
Posts: 2090
Joined: January 9th, 2009, 7:30 pm
Division: Grad
State: OH

Re: Hovercraft B/C

Postby chalker » October 10th, 2016, 4:02 pm

Does not look exactly like the picture that you posted. The kit contains an axial fan. Note it is not plural. It says nothing about anything else for propulsion, but the picture has a large boxed in area at the rear which probably contains a motor driven prop but is not listed in the kit. Why is there the tall mesh over the axial fan which is only a fraction of that height based on what I think I see in the picture.
For the original post, note that this is a get started "also ran" kit. It will not be seriously competitive at any state level competition. That said, the test is 50% of the final score and the craft is the other half.
Not sure what you mean about not looking like what I posted. It's just another one they built in house using the same parts and appears virtually identical to what I previously posted except for the colors of the zip ties.

Note the parts list says motor and plastic propeller in addition to axial fan. The mesh over the axial fan is to provide shielding for it and the reason it's so tall is that's the easiest way to make the shielding work right.

Student Alumni
National Event Supervisor
National Physical Sciences Rules Committee Chair

chalker
Member
Member
Posts: 2090
Joined: January 9th, 2009, 7:30 pm
Division: Grad
State: OH

Re: Hovercraft B/C

Postby chalker » October 10th, 2016, 4:13 pm

That's what you'll get for $107*. You pay the premium to have it all packaged together (and presumably get some sort of instruction sheet) but there's a good chance that between school and home, you have a lot of these items anyway, and a trip to a dollar store or hardware store can fill in the rest. As previously stated, this is a great starting point, and students will be able to build a functional, competition-ready hovercraft. Hopefully they'll find ways to improve on it the more they test it.

*Chalker, can you explain how this price point is set? I assume there's some partnership between Ward's and SO Inc., and this is good business for all parties, but, $107?! Frankly it seems like it's $7 worth of stuff and a $100 packaging fee. If you're contractually obligated not to discuss this, I get it, but all of the online kits seem dramatically overpriced.
I'm not involved in the pricing in any way, but I can share some thoughts on this:

1. Nobody should ever pay the list price for a Ward's Sci kit (or really any science / educational material). All the big companies that do things like this set high list prices then provide lots of various discount codes. There's a code printed in the front of the Rules Manual for 12% off. I know there are other codes floating around for larger discounts as well.

2. Wards does have to recoup labor costs and there is also a certain amount of funding returned for Science Olympiad as well.

3. You're significantly underestimating the cost of the materials. The axial fan, which I've given details on before, costs ~$10 alone. The 9V batteries cost ~$2. Altogether there are something like ~60 different pieces that are included in this kit, which includes extras of things like the foam plate and zip ties so you can build different versions of the hovercraft.

Student Alumni
National Event Supervisor
National Physical Sciences Rules Committee Chair

chalker
Member
Member
Posts: 2090
Joined: January 9th, 2009, 7:30 pm
Division: Grad
State: OH

Re: Hovercraft B/C

Postby chalker » October 10th, 2016, 4:43 pm

Oh, it's more than that. They charge another $18+ shipping and $10+ tax. That is why I have been hesitating in ordering it. I also looked over the list. What I'm not sure about are Motor, Plastic Propeller, Axial Fan: what kind should I buy if I go buy them myself? Also Mesh Squares, what are they for? Wooden Dowels: Balsa wood? How thick? A design that shows what goes where will be helpful.
Note that the kit comes with a 10 page document that gives step by step instructions on how to build the device (with pictures of each step)!

Student Alumni
National Event Supervisor
National Physical Sciences Rules Committee Chair

retired1
Member
Member
Posts: 673
Joined: July 25th, 2012, 5:04 pm
Division: Grad
State: FL

Re: Hovercraft B/C

Postby retired1 » October 10th, 2016, 5:21 pm

I can not find the previous posts for hovercraft.(before the current threads) Anybody have a link. I may owe Chalker an apology.
OK, so it is not a total of $135, it is with a 12% discount on the kit plus fees = $122.++ It is still a starter kit that will require a lot bigger fan to be competitive with the follow on craft. That plus it is on back order--WEN said 54 days.
I have not seen the SO CD for this. If anybody has one, is it a significant help?? For beginners or experienced builders)

chalker
Member
Member
Posts: 2090
Joined: January 9th, 2009, 7:30 pm
Division: Grad
State: OH

Re: Hovercraft B/C

Postby chalker » October 11th, 2016, 5:13 am

I can not find the previous posts for hovercraft.(before the current threads) Anybody have a link.
Here you go: http://www.scioly.org/phpBB3/viewtopic. ... 75#p297165

Student Alumni
National Event Supervisor
National Physical Sciences Rules Committee Chair

retired1
Member
Member
Posts: 673
Joined: July 25th, 2012, 5:04 pm
Division: Grad
State: FL

Re: Hovercraft B/C

Postby retired1 » October 11th, 2016, 5:51 am

Does not look exactly like the picture that you posted. The kit contains an axial fan. Note it is not plural. It says nothing about anything else for propulsion, but the picture has a large boxed in area at the rear which probably contains a motor driven prop but is not listed in the kit. Why is there the tall mesh over the axial fan which is only a fraction of that height based on what I think I see in the picture.
For the original post, note that this is a get started "also ran" kit. It will not be seriously competitive at any state level competition. That said, the test is 50% of the final score and the craft is the other half.
Not sure what you mean about not looking like what I posted. It's just another one they built in house using the same parts and appears virtually identical to what I previously posted except for the colors of the zip ties.

OK, A formal apology. Poor memory. Can I blame it on a different angle?

What are the "boxes" that the push motor is setting on?

Wen
Member
Member
Posts: 9
Joined: October 9th, 2016, 10:03 pm

Re: Hovercraft B/C

Postby Wen » October 11th, 2016, 2:31 pm

Good to see more discussions. Thanks for the large picture, Chalker. It's a little hard to see what are inside the mesh squares.

Could someone comment on this one?
http://www.pitsco.com/Hover-Craft_I?SKU=59661&
Is it useful (or are the parts useful) for SciOly competition? The Props need to be shielded? It's out of stock so not sure how long it will take to get it.

SPP SciO
Member
Member
Posts: 261
Joined: March 24th, 2015, 8:21 am
Division: B
State: NY
Location: Brooklyn

Re: Hovercraft B/C

Postby SPP SciO » October 11th, 2016, 2:39 pm

Good to see more discussions. Thanks for the large picture, Chalker. It's a little hard to see what are inside the mesh squares.

Could someone comment on this one?
http://www.pitsco.com/Hover-Craft_I?SKU=59661&
Is it useful (or are the parts useful) for SciOly competition? The Props need to be shielded? It's out of stock so not sure how long it will take to get it.
Do you have a copy of the rules in hand? I'm not trying to be condescending, at all, but you'll definitely want them in hand before making any purchases.

All of the language about battery-powered motors uses the words "may" or "up to," which don't disallow hovercrafts like that one, or some balloon-style ones you may have seen. So, feel free to experiment - it's certainly less complicated (which can lead to more actual testing and experimenting - the whole point of this competition). But, you'll likely want to have them work on some battery powered craft at some point in the season, and leave the rubber fiddling to the Wright Stuff kids :D

Edit: Rule 4.k - "Vehicles must have an electric switch to permit safe starting." I feel like the intent of the rule was obviously meant for battery powered motors and not to outlaw non-electric vehicles, but, unless that's clarified, play it safe and stick with one of the battery powered models instead.
Coach
MS 821 Sunset Park Prep
http://www.sppscio.com


Return to “2017 Lab Events”

Who is online

Users browsing this forum: No registered users and 0 guests