Wright Stuff C

Locked
Rossyspsce
Member
Member
Posts: 201
Joined: June 3rd, 2018, 5:32 pm
Has thanked: 5 times
Been thanked: 0

Re: Wright Stuff C

Post by Rossyspsce » February 2nd, 2019, 9:30 pm

I was wondering where you guys bought rubber from?

User avatar
klastyioer
Member
Member
Posts: 425
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA
Location: somewhere on planet earth
Has thanked: 1 time
Been thanked: 1 time

Re: Wright Stuff C

Post by klastyioer » February 3rd, 2019, 7:36 am

newflight wrote:I recently ran into an issue with nose down at initial launch with higher torque. I wind rubber band to 1.3 torque and then dewind it to 0.65 torque. When I released it, it will hit on floor after several seconds. Then I picked it up and launched it again, it will fly more than 2 minutes. I then do the same thing to wind torque to 1.3 and dewind it to 0.6. it will fly ok. so, why it cannot fly with higher initial launch torque?
wait so youre winding to 1.3 and then winding backwards to .65 or are you releasing and then letting go so the launch torque is .65
it's not about the medals; go out there and have fun. make progress, learn a few things and have one heck of a time; that's all that matters.

Check out Klastyioer's Userpage!

User avatar
klastyioer
Member
Member
Posts: 425
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA
Location: somewhere on planet earth
Has thanked: 1 time
Been thanked: 1 time

Re: Wright Stuff C

Post by klastyioer » February 3rd, 2019, 7:38 am

Rossyspsce wrote:I was wondering where you guys bought rubber from?
fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
it's not about the medals; go out there and have fun. make progress, learn a few things and have one heck of a time; that's all that matters.

Check out Klastyioer's Userpage!

User avatar
CrayolaCrayon
Member
Member
Posts: 312
Joined: October 25th, 2017, 8:24 am
Division: C
State: DC
Has thanked: 8 times
Been thanked: 1 time

Re: Wright Stuff C

Post by CrayolaCrayon » February 3rd, 2019, 7:54 am

newflight wrote:I recently ran into an issue with nose down at initial launch with higher torque. I wind rubber band to 1.3 torque and then dewind it to 0.65 torque. When I released it, it will hit on floor after several seconds. Then I picked it up and launched it again, it will fly more than 2 minutes. I then do the same thing to wind torque to 1.3 and dewind it to 0.6. it will fly ok. so, why it cannot fly with higher initial launch torque?
I know I had an issue like that once where the prop was angled downwards ever so slightly, and it fought against the lift at the beginning because of the high torque, which made it dive. There might be something more behind your issue, however.
Wright Stuff 2nd 2019 Nationals
USA F1D Team 2020
1391 Turns

jander14indoor
Member
Member
Posts: 1584
Joined: April 30th, 2007, 7:54 am
Has thanked: 0
Been thanked: 1 time

Re: Wright Stuff C

Post by jander14indoor » February 3rd, 2019, 8:29 am

Most likely your fuselage is bending at the higher torques. Pulls the nose down increasing town thrust, and tail down, causing excess nose down moment.

Jeff Anderson
Livonia, MI

Rossyspsce
Member
Member
Posts: 201
Joined: June 3rd, 2018, 5:32 pm
Has thanked: 5 times
Been thanked: 0

Re: Wright Stuff C

Post by Rossyspsce » February 3rd, 2019, 9:08 am

klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?
fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
Do you mind dropping a link, I've only gotten results for volare?

User avatar
klastyioer
Member
Member
Posts: 425
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA
Location: somewhere on planet earth
Has thanked: 1 time
Been thanked: 1 time

Re: Wright Stuff C

Post by klastyioer » February 3rd, 2019, 9:20 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?
fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
Do you mind dropping a link, I've only gotten results for volare?
yea sure
on here u can get other kinds but i attached one that you may be interesting in. warning you'll need a rubber stripper if you purchase this
https://www.faimodelsupply.com/product/ ... rt-rubber/
it's not about the medals; go out there and have fun. make progress, learn a few things and have one heck of a time; that's all that matters.

Check out Klastyioer's Userpage!

User avatar
CrayolaCrayon
Member
Member
Posts: 312
Joined: October 25th, 2017, 8:24 am
Division: C
State: DC
Has thanked: 8 times
Been thanked: 1 time

Re: Wright Stuff C

Post by CrayolaCrayon » February 3rd, 2019, 9:20 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?
fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
Do you mind dropping a link, I've only gotten results for volare?
https://www.faimodelsupply.com/product- ... rt-rubber/
Wright Stuff 2nd 2019 Nationals
USA F1D Team 2020
1391 Turns

User avatar
klastyioer
Member
Member
Posts: 425
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA
Location: somewhere on planet earth
Has thanked: 1 time
Been thanked: 1 time

Re: Wright Stuff C

Post by klastyioer » February 3rd, 2019, 9:23 am

Rossyspsce wrote:
klastyioer wrote:
Rossyspsce wrote:I was wondering where you guys bought rubber from?
fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
Do you mind dropping a link, I've only gotten results for volare?
honestly buy whatever size and amount u want
it's not about the medals; go out there and have fun. make progress, learn a few things and have one heck of a time; that's all that matters.

Check out Klastyioer's Userpage!

Rossyspsce
Member
Member
Posts: 201
Joined: June 3rd, 2018, 5:32 pm
Has thanked: 5 times
Been thanked: 0

Re: Wright Stuff C

Post by Rossyspsce » February 3rd, 2019, 9:33 am

klastyioer wrote:
Rossyspsce wrote:
klastyioer wrote: fai rubber supply, some ppl buy from like freedom flight cause its just easier if youre gonna buy other things from their website, but i usually buy from fai
Do you mind dropping a link, I've only gotten results for volare?
yea sure
on here u can get other kinds but i attached one that you may be interesting in. warning you'll need a rubber stripper if you purchase this
https://www.faimodelsupply.com/product/ ... rt-rubber/
For the rubber stripper part, is this true for all rubber that comes in box?

Edit: for example the description of this rubber is 3/32" so I would assume that it comes precut into a 3/32" strand? https://www.faimodelsupply.com/product/ ... rt-rubber/

Locked

Return to “Wright Stuff C”

Who is online

Users browsing this forum: No registered users and 0 guests