## Machines B/C

Justin72835
Member
Posts: 175
Joined: June 25th, 2017, 7:06 am
State: TX

### Re: Machines B/C

You wish to raise one side of a 5,000 kg car to change a flat tire. You have a strong 2x4 to use as a lever, and a 15 cm high block for a fulcrum. The fulcrum is 304,000 µm from the load, and the lever is 1.52 × 10^-6 Mm long. How much force is needed to lift the car? Give your answer in kg.

Assume that the jack point is in the middle of the side, and that you need to lift half of the car's mass.

Sorry if that's not allowed by the rules or is overly complicated. I ain't read the rules that closely yet.

Hint: Not all of the values given are needed. It should be a simple formula.
Before solving, I just want to note that force is measured in Newtons, so I'll give my answer in both kilograms and Newtons .

1250 kg or 12250 N
The kg/N thing was my error... I wanted the answer in Newtons.
If you'd've showed your work in some form, I wouldn't've hadta compute it myself...
I got this:
(0.5×5000kg)(9.80566m/s^2)(0.304m)(1.216m)=9061.998746 Newtons.

9060 N
{I don't round until I get my final answer, so I allow for a little fluctuation...}

Notes: You may have made one or more of the following errors. Without your work, it's hard to tell which.
Mm is Megameters, which converts to 1.52m. But, I gave the total length of the lever here, not the force-fulcrum distance. With that subtracted, you get 1.216m.
µm is micrometers, which converts to 1.304m.
My answer seems a little high, but with made-up values... I tried running it through online calculators, but I wound up with 5 answers from 3 different calculators, without changing anything and with the correct units...

Edit: I might not have the right formula...
Turns out I missed the first part about raising one side heh. Anyway, looking at your work, you should be dividing by 1.216, not multiplying. When you divide by that you get 6125 N, which is half of my original answer.

If you're interested in the formula: F1*d1=F2*d2
"The fault, dear Brutus, is not in our stars,
But in ourselves, that we are underlings."

University of Texas at Austin '23
Seven Lakes High School '19

Things2do
Member
Posts: 125
Joined: February 12th, 2018, 2:30 pm
Division: C
State: TN
Location: Unfortunately, not Utah somewhere near the Colorado border

### Re: Machines B/C

Before solving, I just want to note that force is measured in Newtons, so I'll give my answer in both kilograms and Newtons :D.

1250 kg or 12250 N
The kg/N thing was my error... I wanted the answer in Newtons.
If you'd've showed your work in some form, I wouldn't've hadta compute it myself...
I got this:
(0.5×5000kg)(9.80566m/s^2)(0.304m)(1.216m)=9061.998746 Newtons.

9060 N
{I don't round until I get my final answer, so I allow for a little fluctuation...}

Notes: You may have made one or more of the following errors. Without your work, it's hard to tell which.
Mm is Megameters, which converts to 1.52m. But, I gave the total length of the lever here, not the force-fulcrum distance. With that subtracted, you get 1.216m.
µm is micrometers, which converts to 1.304m.
My answer seems a little high, but with made-up values... I tried running it through online calculators, but I wound up with 5 answers from 3 different calculators, without changing anything and with the correct units...

Edit: I might not have the right formula...
Turns out I missed the first part about raising one side heh. Anyway, looking at your work, you should be dividing by 1.216, not multiplying. When you divide by that you get 6125 N, which is half of my original answer.

If you're interested in the formula: F1*d1=F2*d2
I figured that I was supposed to divide somewhere in there... Anyways, it's your turn.
John 5:46-47
When your signature exceeds the allotted 300 characters, you put it here...
Is this where I put the Builder Cult?
"I think that we're all mentally ill. Those of us outside the asylums only hide it a little better - and maybe not all that much better after all." - Stephen King

Justin72835
Member
Posts: 175
Joined: June 25th, 2017, 7:06 am
State: TX

### Re: Machines B/C

What is the IMA of an inclined plane with an angle of 35 degrees?
"The fault, dear Brutus, is not in our stars,
But in ourselves, that we are underlings."

University of Texas at Austin '23
Seven Lakes High School '19

Creationist127
Member
Posts: 38
Joined: August 14th, 2018, 3:21 pm
Division: C
State: IN
Location: On a train, traveling from Kalos to Galar

### Re: Machines B/C

What is the IMA of an inclined plane with an angle of 35 degrees?
Would it be 1.7?
2018: Hovercraft, Thermo, Coaster, Solar System
2019: Thermo, Circuit Lab, Sounds, Wright Stuff
2020: Circuit Lab, Chem Lab, Wright Stuff, Machines

The grind begins now!

Justin72835
Member
Posts: 175
Joined: June 25th, 2017, 7:06 am
State: TX

### Re: Machines B/C

Would it be 1.7?
"The fault, dear Brutus, is not in our stars,
But in ourselves, that we are underlings."

University of Texas at Austin '23
Seven Lakes High School '19

Creationist127
Member
Posts: 38
Joined: August 14th, 2018, 3:21 pm
Division: C
State: IN
Location: On a train, traveling from Kalos to Galar

### Re: Machines B/C

A wedge is 1 inch thick and has a 25* angle at its narrow edge. It is placed with the thin edge in a crack in a block of wood. If 5 newtons of force is exerted on the end, how much force will the wedge split the block with?
2018: Hovercraft, Thermo, Coaster, Solar System
2019: Thermo, Circuit Lab, Sounds, Wright Stuff
2020: Circuit Lab, Chem Lab, Wright Stuff, Machines

The grind begins now!

amk578
Member
Posts: 106
Joined: December 5th, 2018, 5:21 pm
Division: C
State: IN

### Re: Machines B/C

A wedge is 1 inch thick and has a 25* angle at its narrow edge. It is placed with the thin edge in a crack in a block of wood. If 5 newtons of force is exerted on the end, how much force will the wedge split the block with?
11.25 N or 10 N w/ sig figs
```2018 - Anatomy, Crime Busters, & Road Scholar
2019 - Anatomy, Disease Detectives, Heredity, & Road Scholar```
2020 - Anatomy, Designer Genes, Disease Detectives, Forensics, PPP, & Protein Modeling

Creationist127
Member
Posts: 38
Joined: August 14th, 2018, 3:21 pm
Division: C
State: IN
Location: On a train, traveling from Kalos to Galar

### Re: Machines B/C

A wedge is 1 inch thick and has a 25* angle at its narrow edge. It is placed with the thin edge in a crack in a block of wood. If 5 newtons of force is exerted on the end, how much force will the wedge split the block with?
11.25 N or 10 N w/ sig figs
2018: Hovercraft, Thermo, Coaster, Solar System
2019: Thermo, Circuit Lab, Sounds, Wright Stuff
2020: Circuit Lab, Chem Lab, Wright Stuff, Machines

The grind begins now!

amk578
Member
Posts: 106
Joined: December 5th, 2018, 5:21 pm
Division: C
State: IN

### Re: Machines B/C

Which of the following screws has the highest mechanical advantage?

a) a screw with a (1/2) inch radius with 10 threads per inch
b) a screw with a (1/2) inch radius with 12 threads per inch
c) a screw with a (1/4) inch radius and 10 threads per inch
d) a screw with a (1/4) inch radius and 12 threads per inch
```2018 - Anatomy, Crime Busters, & Road Scholar
2019 - Anatomy, Disease Detectives, Heredity, & Road Scholar```
2020 - Anatomy, Designer Genes, Disease Detectives, Forensics, PPP, & Protein Modeling

CPScienceDude
Member
Posts: 166
Joined: December 12th, 2018, 2:40 pm
Division: C
State: IN
Location: Crown Point High School

### Re: Machines B/C

B?
CPHS 23'
2020 events: Ornithology, Machines, Gravity Vehicle, and Forensics
Member of the Builder Cult
Assassination 139: Summer Vacation

### Who is online

Users browsing this forum: No registered users and 2 guests