2020 Wright Stuff Parameters

User avatar
klastyioer
Member
Member
Posts: 404
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: 2020 Wright Stuff Parameters

Postby klastyioer » June 12th, 2019, 6:01 pm

okay so im looking at the cezar banks one and im kinda confused on what they mean by the sq round nose thing for the leading edge
is that sanding to taper like a triangle like shape?
and i dont get what the tapering is on the winglets
i have a 4 in radius can i currently use for my ws props and i know it says use a gallon jug for the prop molding, but i dont have one. is there a way to convert the angles to my jar instead?
lastly, any tips for making rib templates? i havent made them this year my teammates have and i wont really see them this summer so i dont really have any idea on how to go about those
it's not about the medals; go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.

Builder Cult >:)

'17 - Towers, WS, rocks
'18 - Towers, WS, Mystery Arch, road
'19 - WS
'20 - WS, Boomilever, PPP

jander14indoor
Member
Member
Posts: 1553
Joined: April 30th, 2007, 7:54 am
State: -

Re: 2020 Wright Stuff Parameters

Postby jander14indoor » June 12th, 2019, 6:57 pm

Probably getting to point that you'd be better asking these on some of the free flight forums as suggested. That said...
...I'll give MY view.

Rounded nose spars. Just what it sounds like. Round off the top and bottom LEADING corners of the leading spar. Start with a square 1/16 spar and round two edges. Meant to improve airflow and it doesn't take much. Not sure how critical it is, but at top levels of competition, you start seeing things where competitors try to reduce drag by such actions to the leading edge. Before there were so many carbon fiber spars in SO, some of the designs had triangular shaped leading edge spars for the same reason.

Tapering on the winglets is to reduce weight. Hitting weight on an LPP is very doable, but not if you don't pay attention. Less stress at tips, so need less material. You do it by taking a sheet of material (the length of the tip spars) you plan on making the tips from and carefully sanding in the desired taper on one face. Obviously along the grain. Then you cut out your tip spars on a taper, a jig of some sort is real handy there. You end up with triangles of waste balsa with taper in the wrong direction between your tapered spars that you just discard.

Prop making. Yes there are programs to figure out what angle and ideal diameter to use to form a prop to a reasonable approximation of a helical prop. While a given diameter can be used for a range of prop pitch/diameter combinations, there are limits. If you don't have a gallon jug, do you have a small pail of similar diameter? Could you get some tin from the hardware store and form your own cylindrical (or actually more accurate, a frustrum) form? Alternatively, if you have a bunch of spare balsa, you can make a true helical blade form pretty easy.

Rib templates are pretty easy. I like to make them from Mat Board, the cardboard backs of pads of paper can be good. I had a long explanation, but again, Indoor News and Views is your friend. See page 87 of https://indoornewsandviews.files.wordpr ... f-inav.pdf I like to reinforce the curved edge by soaking it with CA and wiping off the excess. If you are careful it will last a LONG time. As to the exact curve, for that plan the recommendation is a simple arc. It works.

If you haven't already, read the Hobby Shopper and the “My Way” Penny Plane construction on that same link. INAV has a wealth of knowledge.

Hope that helps,

Jeff Anderson
Livonia, MI

User avatar
klastyioer
Member
Member
Posts: 404
Joined: April 22nd, 2018, 4:46 pm
Division: C
State: PA

Re: 2020 Wright Stuff Parameters

Postby klastyioer » June 15th, 2019, 8:35 am

yes it helped a lot, thanks so much
i probably will switch over to hpa for the summer, but it all depends on what i do
thanks again

katie
it's not about the medals; go out there and have fun. make progress, learn a few things, have one heck of a time, because that's all that matters.

Builder Cult >:)

'17 - Towers, WS, rocks
'18 - Towers, WS, Mystery Arch, road
'19 - WS
'20 - WS, Boomilever, PPP

noah.blome21
Member
Member
Posts: 10
Joined: March 15th, 2018, 7:20 am
Division: C
State: IL

Re: 2020 Wright Stuff Parameters

Postby noah.blome21 » August 26th, 2019, 10:12 am

ok
Last edited by noah.blome21 on August 26th, 2019, 5:58 pm, edited 1 time in total.

bjt4888
Member
Member
Posts: 508
Joined: June 16th, 2013, 12:35 pm
Division: C
State: MI

Re: 2020 Wright Stuff Parameters

Postby bjt4888 » August 26th, 2019, 5:20 pm

See Chris Goins’ Double Trouble Wright Stuff biplane design for ideas.

This plan is posted on Hip Pocket Aero Builders Plan Gallery in “Indoor/Other Classes”.

Brian T


Return to “Wright Stuff C”

Who is online

Users browsing this forum: No registered users and 1 guest