Wind Power
Wind Power  

Type  Physics  
Category  Lab  
Forum Threads  
 
 
 
Forum Question Threads  

Wind Power, previously known as Physical Science Lab and Physics Lab, is an event for the 2017 season which involves the construction of a device that can turn wind into energy and the answering of questions relating to alternative energy.
Contents
The Basics of the Event
Half of the scoring for Wind Power comes from the building portion. Competitors must build a wind turbine mounted to an unmodified 12cm diameter CD. During competition, the judges will attach the device to a DC motor. They will then place a fan in front of the device and turn it on. The blades will spin, thereby creating voltage.
The other portion of the event is a written test on wind power, power generation, and alternative energy. One 3ring binder full of notes from any source is allowed for each team, as long as the material in the binder is attached securely. Teams may bring multiple calculators of any type.
Category B safety spectacles are required for the blade testing portion of this event.
The Building Section
This page requires cleanup to meet the wiki's quality standards. Please help by editing this page if you can. 
Examples: Blades for 2017
When you plan to build your device, there are many factors to consider. Some of them include:
 Wind Turbine Diameter
 Weight
 Blade Width
 Blade Thickness
 Curve of the Blade
 Blade Pitch
 Number of Blades
 Blade Material
This event has changed since 2016. Instead of trying to get the blades to spin as fast as possible with no resistance, you have 5 to 25 ohms of resistance the blades have to 'push' against, which will be wired into the setup. You can buy resistors of varying size or wire 2 in parallel. For example, two 14 ohm resistors in parallel = 7 ohms of resistance.
Weight
Lighter blades will spin faster, but since in 2017 you must produce power (due to the resistors), a slightly heavier blade will have a higher momentum. There will be 2.5 minutes of preparation in order to get the blades up to highest attainable speed, so they can be somewhat heavy.
Blade Material
Various items can be used to construct the blades, but any type of metal is not allowed. Balsa wood or paper are often used for they are lighter materials. Everyday items can often be constructed into blades. For example, a plastic cup can be cut into fourths. Keep experimenting with different materials.
Diameter
According to the New York Coaches Conference, doubling the diameter of the circle made by the blades produces a 4fold increase in power. However, keep in mind that the radius of the circle created by the blades can be no more than 20cm (Div B) and 14cm (Div C).
Many teams have found that since real life wind turbines can create more power (watts, not voltage) by increasing the diameter of the blades, it is to your advantage to do so.
Blade Curvature
It is advised that the blade contains some curve, although it is not necessary in order to generate spin. A Vshape might also work. Materials may be morphed into the desired shape whether it be by cutting or molding. With some materials, such as wood, a certain shape can be achieved by soaking and bending the material in water. Not much curve is necessary. It is recommended that the blades have a curve to simulate an airfoil, while still keeping the blades aerodynamic. Keep in mind that more force is generated when the wind from the fan is blowing on the outside of the blade curve, but this is not what most people do. Most people curve it so that the wind hits the inside of the curve, as this provides quick acceleration (which isn't totally necessary, as long as it accelerates to top speed within 2.5 minutes), but also resulting in a top speed that is lower than if the wind was on the outside of the blade.
Blade Pitch
Blade pitch refers to the angle of the blades relative to the CD. Generally, a lower pitch results in a higher speed and thus a higher power (it will have a much slower acceleration but a higher top speed). One may want a higher pitch the closer the blade gets to the center of the turbine (eg. 20 degrees towards the center and make the front edge gradually get lower until around 510 degrees or so at the outside). Make sure your blade pitch is not 0 degrees, as the blades will not generate lift.
Number of Blades
The number of blades is another adjustable variable. 23 blades is the most popular amount. Remember that more weight will gain more momentum, but at a point, too much weight will lower the high speed of the turbine. 4 or more blades can often be too heavy if the material is not light enough. However, if the blades are light enough, 4 may work better than 2 or 3.
Balance
Balance is also an important factor. If a turbine is terribly off balance, it may wobble on the mount, and possibly even break. As such, a wellbalanced turbine will be able to spin faster since there will be less friction against the mount and less energy will be lost to vibration. It is best if a turbine's center of gravity is at or near the center. This can be accomplished by taking some mass off of the turbine on the heavy side, or by adding mass on the lighter side. A way to help make sure that you build your blade as balanced as possible is to make a device with a thin 1ft by 1ft thin piece of plywood with a metal/wood rod sticking straight out, and lines can be drawn on the sheet of ply going away from the rod at equal increments for which you can line up your blades as you glue them to the CD.
Although it may otherwise be a good idea, the rules say that "modification of the CD is not allowed (except to affix the blades via tape, glue, etc.)".
Make sure that your turbine is clearly within specs and labeled with your team's name and number.
The Written Section
This page is outdated. The information it provides needs to be updated to reflect changes in the event rules or recent scientific developments. Please keep this in mind when reading the page and add updated information if possible. 
The other half of the score is the written portion. The rules recommend that teams look at Alliant Energy and American Wind Energy Association.
Alternative Energy
Alternative energy is generally defined as energy that does not harm the environment directly. They usually do not produce carbon emissions and many times they are also renewable. There are several types of renewable energy, each with its own advantages and disadvantages.
 Solar power converts sunlight into energy via photovoltaic panels or concentration. In the longterm it is relatively constant; however, days are longer in the summer and shorter in the winter, resulting in less solar energy generated in the winter. Also, solar power is only available during the day and is less powerful when there are many clouds.
 Wind power converts the kinetic energy of the wind into other forms of energy, usually into electrical energy with turbines. Wind is plentiful and the method has no emissions, but turbines can be unwelcome both visually and environmentally. Also, periods of wind are more unpredictable than some other methods.
 Hydroelectric power converts the movement of water into energy, generally with turbines as well. The flow of water is abundant, constant, and hydroelectric plants can store energy for times when it is more necessary, but there are concerns in respect to the reservoirs created by dams.
 Tidal power is a major subset of hydroelectric power. It uses the movement of water created by tides to get energy. Tides are regular and predictable, but less power can be generated this way than some other ways.
 Ocean Thermal Energy Conversion (OTEC) utilizes the difference in temperature from shallow water to deeper water. When heat goes from the warmer water to cooler water, an engine converts the flow to energy. This is constant, but not very costeffective and finding locations where this technology can be used is difficult.
 Geothermal power converts underground heat into energy. This method is reliable, costeffective, and environmentally friendly, but is mostly limited to areas with a high tectonic activity.
To conserve energy, the adage "reduce, reuse, recycle" can be followed. These three concepts can be applied to many techniques used to conserve energy.
Energy
Energy is the capacity to perform work. Work, in turn, is when a force is exerted on an object and the object moves parallel to the direction of the force. Work, in joules (J), can be calculated by multiplying the force applied in Newtons (N) to the distance traveled in meters (m). Power is the rate at which this work is performed, and is found by dividing the work by the time. It is measured in watts.
There are two major types of energy:
 Kinetic energy is the energy contained by an object in motion
 Potential energy is how much work an outside force like gravity can do on an object depending on its position.
The Conservation of Energy principle states that energy cannot be created nor destroyed, and that it can only be transformed from one form to another.
Heat
Heat is the transfer of energy from a hightemperature object to a lowtemperature object.
Temperature
Temperature is the average energy contained in the particles of an object. It is produced by the thermal energy in free particles. Many scales can measure temperature.
Heat Transfer
There are three main vehicles for transferring heat:
 Conduction is the transfer of heat by direct contact. The heat transfer for convection can be calculated by the following formula:
 [math]Q=\frac {kA\left (T_{hot}T_{cold}\right )}{d}[/math]
 Where
 Q is the heat transferred in [math]Watts[/math]
 k is the barrier's thermal conductivity in [math]k=\frac {Watts}{m K}[/math]
 A is the crosssectional area in [math]m^2[/math]
 T is the temperature in °C ([math]T_{hot}[/math] represents the warmer temperature and [math]T_{cold}[/math] represents the cooler temperature)
 d is the barrier's length in [math]m[/math]
 Convection is the transfer of heat from a solid or liquid to another fluid. Forced convection is a fluid flowing over a surface. Natural convection is when a fluid is heated and rises due to buoyancy such as when hot air rises and cooler air sinks, creating circular currents. The heat transfer for convection can be calculated by the following formula:
 [math]Q=hA(T_{hot}T_{cold})[/math]
 Where
 Q is the heat transferred in [math]Watts[/math]
 h is the film coefficient in [math]h=\frac{watts}{m^2 K}[/math]
 A is the surface area in contact with the fluid in [math]m^2[/math]
 T is the temperature in °C ([math]T_{hot}[/math] represents the warmer temperature and [math]T_{cold}[/math] represents the cooler temperature)
 Radiation is where the heat is carried by electromagnetic waves. The StefanBoltzmann Law can help calculate this transfer:
 [math]P=e\sigma A \left (T^4{T_C}^4\right )[/math]
 Where
 P is the radiated power in [math]Watts[/math]
 e is the object's emissivity
 σ is Stefan's constant (equal to [math]5.6703 \cdot10^{8} \frac {W}{m^2K^4}[/math])
 A is the radiating area in [math]m^2[/math]
 T is the temperature of the radiating source in K and [math]T_C[/math] is the surrounding temperature.
Specific Heat
This is the amount of heat per unit mass needed to raise a substance's temperature by 1 °C. It is represented by the following formula:
[math]Q=mC\Delta T[/math]
Where Q is the heat needed, C is the specific heat, m is the mass, and ΔT is the change in temperature. Every substance has its own specific heat. For example, water's specific heat is 4.184 J/g*K
Laws
Betz’ law/limit
Only a certain amount of energy can be harnessed from the wind; 59.3%; the theoretical maximum coefficient of power for any wind turbine.
Joule's Law
Energy losses are directly proportional to the square of the current. Thus, reducing the current by a factor of two will lower the energy lost to conductor resistance by a factor of four for any given size of conductor.
Kelvin's Law
The optimum size of a conductor for a given voltage and current can be estimated by Kelvin's law for conductor size. Kevin's Law states that the size is at its optimum when the annual cost of energy wasted in the resistance is equal to the annual capital charges of providing the conductor. At times of lower interest rates, Kelvin's law indicates that thicker wires are optimal; while, when metals are expensive, thinner conductors are indicated: however, power lines are designed for longterm use, so Kelvin's law has to be used in conjunction with longterm estimates of the price of copper and aluminum as well as interest rates for capital.
Laws of Thermodynamics
 Zeroth Law of Thermodynamics: If two systems are each in thermal equilibrium with a third, they are also in thermal equilibrium with each other.
 First Law of Thermodynamics (also known as Law of Conservation of Energy): Energy cannot be created or destroyed in an isolated system.
 Second Law of Thermodynamics: The entropy of any isolated system always increases.
 Third Law of Thermodynamics: The entropy of a system approaches a constant value as the temperature approaches absolute zero.
History
 1881: The transmission of electric power with alternating current (AC) became possible after Lucien Gaulard and John Dixon Gibbs built what they called the secondary generator, an early transformer provided with 1:1 turn ratio and open magnetic circuit.
 1887: The first electricitygenerating wind turbine was a battery charging machine installed by Scottish academic James Blyth to light his holiday home in Marykirk, Scotland.
 1888: American inventor Charles F. Brush built the first automatically operated wind turbine.
 1891: Danish scientist Poul la Cour constructed a wind turbine to generate electricity, which was used to produce hydrogen by electrolysis. With his Askov mill, he made windmills more efficient.
 1919: German physicist Albert Betz discovered the theory of wind energy.
The Competition
For the building setup, there will be 2 stations: high speed and low speed. These may be at the same fan, but if they are at different fans, all teams will test at high speed at one and at low speed at the other. The event supervisors will provide the testing mount for your blades (don't bring your stand, ONLY the cd with blades attached). They will also provide the fan, motor/generator, load resistor, and device to measure voltage. There is a 3minute time limit for each station. You will get a warning at 2 minutes. In the first 2.5 minutes, you may adjust, modify, and start and stop your blades. Within 2.5 minutes of the start of the testing period, you must tell the ES to begin measuring your voltage for 30 seconds. The ES must record the peak voltage that is measured during that period.
The written test will take place after impound. If a lengthier test is used for the event, teams will be called up separately to stations and resume the written portion after testing their build.
Scoring
As of 2017, the scoring for the building section is calculated as follows:
The maximum possible score on the building section is 50.
As of 2017, the scoring for the test section is calculated as follows:
The maximum possible score on the test section is 50.
The test score and the building score are added together to determine a team's score, with the highest score winning.